|
Remark
|
Approved
|
Checked
|
Inspector
|
|
|
|
周小平
|
|
贴片铝电解电容封装
● 卷盘图样、尺寸
|
SIZE
|
A
|
B
|
C
|
D
|
E
|
W
|
t
|
|
A、B
|
385±2
|
80min
|
13±0.5
|
21±0.8
|
2.0±0.5
|
14±1
|
3.0
|
|
C（H）、D
|
385±2
|
80min
|
13±0.5
|
21±0.8
|
2.0±0.5
|
18±1
|
3.0
|
|
E、F
|
385±2
|
80min
|
13±0.5
|
21±0.8
|
2.0±0.5
|
26±1
|
3.0
|
● 编带图样、尺寸
|
SIZE
|
W
|
A
|
B
|
P0±0.1
|
P1
|
P2±0.1
|
F
|
ΦD0+0.1
|
t1
|
E
|
t2
|
|
A
|
12.0
|
4.7
|
4.7
|
4.0
|
8.0
|
2.0
|
5.5
|
1.5
|
0.4
|
1.75
|
5.8
|
|
B
|
12.0
|
6.0
|
6.0
|
4.0
|
12.0
|
2.0
|
5.5
|
1.5
|
0.4
|
1.75
|
5.8
|
|
C
|
16.0
|
7.0
|
7.0
|
4.0
|
12.0
|
2.0
|
7.5
|
1.5
|
0.4
|
1.75
|
5.8
|
|
CH
|
16.0
|
7.0
|
7.0
|
4.0
|
12.0
|
2.0
|
7.5
|
1.5
|
0.4
|
1.75
|
8.3
|
|
D
|
16.0
|
8.7
|
8.7
|
4.0
|
12.0
|
2.0
|
7.5
|
1.5
|
0.4
|
1.75
|
6.8
|
|
E
|
24.0
|
8.7
|
8.7
|
4.0
|
16.0
|
2.0
|
11.5
|
1.5
|
0.4
|
1.75
|
11.0
|
|
F
|
24.0
|
10.7
|
10.7
|
4.0
|
16.0
|
2.0
|
11.5
|
1.5
|
0.4
|
1.75
|
11.0
|
包装数量
|
SIZE CODE
|
ΦD
|
L
|
内包装
|
外包装
|
|
A
|
4
|
5.4
|
2000
|
20000
|
|
B
|
5
|
5.4
|
1000
|
10000
|
|
C
|
6.3
|
5.4
|
1000
|
8000
|
|
CH
|
6.3
|
7.7
|
1000
|
8000
|
|
D
|
8
|
6.5
|
1000
|
8000
|
|
E
|
8
|
10.3
|
500
|
3000
|
|
F
|
10
|
10.3
|
500
|
3000
|
贴片式铝电解电容器
REFLOW SOLDERING CONDITIONS 回流焊条件
1.A thermal conditions system such as infrared radiation (IR) or hot blast shall be adopted, and vapor heat transfer systems (VPS) are not recommended.
应采用红外线或热风回流焊接，而不宜采用汽相加热回流焊接。
2.Reflow shall be done within 2 cycles. Please make sure that the parts have enough cooling time.
回流次数 2次，请确保在第1次和第2次之间产品有足够的冷却时间。
3.-the time of preheating from 150 ℃ to 200 ℃ shall be within 180 seconds maximum;
从150 ℃至200℃的预热时间在180秒钟以内；
-the time of soldering temperature at217℃ measured on capacitors’ top shall not exceed tL(second);
电容器顶部温度超过217 ℃的焊接时间不得超过tL（ 秒）；
-the peak temperature on capacitors’ top shall not exceed Tp (℃), and the time within 5℃ of actual peak temperature shall not exceed tp (second).
电容器顶部的尖峰温度不超过TP（℃），在5℃范围内的实际尖峰温度不得超过tp(秒)。
□Classification Reflow Profile 回流焊曲线图
＊1.Average ramp-up rate is 3℃/second max. 温度上升平均每秒钟 3℃.
＊2.Ramp-down rate is 6℃/second max. 温度下降平均每秒钟 6℃.
＊3.Time form 25℃ to peak temperature is 8minutes max. 从25℃上升到尖峰温度时间 8分钟。
□Classified at Temperature and Time 温度和时间分类
|
Size
|
Thickness(mm)
|
Volume(mm3)
|
TP(℃)
|
tL(second)
|
tp(second)
|
|
Φ4~Φ6.3& Φ8*6.5L
|
≥2.5
|
<350
|
255±5
|
60
|
15
|
|
Φ8*10.5L
|
≥2.5
|
350~2000
|
245±5
|
60
|
15
|
|
Φ10*10.5L
|
≥2.5
|
350~2000
|
240±5
|
60
|
15
|
